seagate freeagent goflex not recognized set address failed

#Seagate freeagent goflex not recognized set address failed windows 10
#Seagate freeagent goflex not recognized set address failed pro
#Seagate freeagent goflex not recognized set address failed code
#Seagate freeagent goflex not recognized set address failed windows

I used sudo nautilus to erase all the folders I made there.ĭo I need to do anything else to clear out possible commands? power saving mode to 'never' I think, and keep trying. Will try the power down issue using windows, as suggested, tho they didn't say what to do, set standby to '0'? still not sure what I am supposed to adjust to what. or maybe the chown command I used was wrong, for a usb device? perhaps a chmod on the directory if I use fstab, or the fstab line.though seems I shouldn't need it as a usb device. ? Expect I missed something simple and as I still don't really understand how it all works under the hood. Anyway, should plug and play like other USB drives.'should' oh well. though seems the problem is something else all together. Oh used the sudo nautilus to delete the dir I created in case it was getting in the way.

#Seagate freeagent goflex not recognized set address failed code

Uncomment fstab (using original line), changes to error code 1 again, but can use disk utility to safely remove drive All Linux since then.īut in XP it mounted fine, all there, ran checkdisk, no problems, disconnected normal.īack to linux machine, error code 13 still,

#Seagate freeagent goflex not recognized set address failed windows

Hooked up to Windows machine (had to find one) only Windows I run is W98 for legacy. Ntfs-3g defaults,user,locale=en_US.utf8 0 0īack to as before and comment out for now Either mount the volume as root, or rebuild NTFS-3G with integratedįUSE support and make it setuid root. Unprivileged user can not mount NTFS block devices using the external FUSE Get exit code 13 message in terminal then Sudo mount -t ntfs-3g /dev/sdb1 /media/external (from 'mount/USB' thread)

Uncomment fstab line and back to can't mount. Sudo mount says special device does not existĬomment out fstab line, back to beginning Reboot, splashscreen message to S skip mount of media/E-1 or M manual, pick S Mount: only root can mount /dev/sdc1 on /media/Ext-1 Gparted cant act on it, will try and fail with same message aboveĮrror mounting: mount exited with exit code 1: helper failed with: Please see the 'dmraid' documentationĭisk utility could see drive as /dev/sdc1 and had specs, can't check or format though shows volume. It and mount a different device under the /dev/mapper/ directory, (e.g. Important! If the device is a SoftRAID/FakeRAID then first activate

In the first case run chkdsk /f on Windows NTFS is either inconsistent, or there is a hardware fault, or it's a I am going to try this and will report back if it does not fix it.Have found many posts on this issue, no solutions work or match just what I get, maybe my experience will help figure it out.įailed with this error: repeating endlessly, as it kept trying endlesslyĮrror mounting: mount exited with exit code 13: ntfs_attr_pread_i: ntfs_pread failed: Input/output errorįailed to read NTFS $Bitmap: Input/output error I don't believe the cable is bad because it works fine on another machine with the same usb cable. I've tried switching usb ports but same result. I have 2 other external drives connected to it, an external WD 12GB and a smaller 4GB 3rd party external enclosure, all working fine. Since the enclosure works in another computer I assume there is something wrong with the specific machine. If I reboot the computer sometimes the drive will be recognized and sometimes it won't. The only way I can get it to recognize it to power cycle the enclosure but the problem occurs again. While the drive is in the Unknown USB Device (Set Address Failed) state, I uninstall the driver, rescanned hardware and it pops up again as Unknown USB Device (Set Address Failed). I can write and delete to it and no problems, no freezes, no disconnects. So I moved it over to another machine, running same windows version and it works fine. I can toggle the power on the enclosure but as soon as I try to write something to it or even delete something explorer freezes and disconnects the enclosure. I checked out device manager and it showed Unknown USB Device (Set Address Failed). A couple days ago after I performed a Windows update, the drive started to disconnect when attempting to write data to it.

#Seagate freeagent goflex not recognized set address failed windows 10

I've had this enclosure connected to a Windows 10 machines for several months now with no hiccups. Enclosure specs are here HUR5-SU31C, 2 Bay USB 3.1 Type-C Specs - Mediasonic Forum I am running a WD RED 10GB RAID 1 mirror on an unmanaged external enclosure.

#Seagate freeagent goflex not recognized set address failed pro

Windows version 21H1 19043-985 Windows 10 Pro 64bit